Most cap projects are specified from the wrong end. A buyer asks for a quotation for "a machine", and only later discovers that cavity count, maximum cap diameter and real running speed are three separate limits - and that not every model can run every cap. Starting from the cap, not from the quotation, is the difference between a line that pays back in two years and one that is rebuilt in three.
Why compression molding, not injection molding
In compression molding, resin pellets are plasticized, cut into a precise shot and dropped into an open, temperature-controlled mold. A rotating turntable then presses the cap into its final shape under controlled pressure. There is no runner and no sprue, so there is nothing to regrind: material utilization approaches 100 percent, cap weight stays inside a narrow band cycle after cycle, and the finished surface carries no gate mark. Because the melt travels a far shorter flow path than in injection molding, the process also uses less energy per cap. For water, CSD, dairy and large-format closures, that combination of weight consistency and cosmetic quality is what makes high-speed production economical rather than merely fast.
Five platforms, 24 to 64 cavities
JEEPINE builds this platform in five cavity configurations, covering 24,000 to 150,000 caps per hour. Every figure below is from the published model specification sheet.
|
Model |
Cavities |
Max output |
Max cap OD |
Max cap height |
Max cap weight |
|
CCM-YSZG64 |
64 |
150,000 pcs/h |
Φ45 mm |
22 mm |
4 g |
|
CCM-YSZG54 |
54 |
100,000 pcs/h |
Φ35 mm |
25 mm |
4 g |
|
CCM-YSZG48 |
48 |
85,000 pcs/h |
Φ45 mm |
25 mm |
6.5 g |
|
CCM-YSZG24 |
24 |
40,000 pcs/h |
Φ55 mm |
25 mm |
7.5 g |
|
CCM-JP24 |
24 |
24,000 pcs/h |
Φ55 mm |
30 mm |
7.5 g |
The CCM-YSZG64 is the flagship: 64 cavities in synchronized molding, 150,000 caps per hour, built for leading producers in beverage, personal care and pharmaceutical packaging as well as large cap OEMs. At that speed the value is not the peak number on the datasheet but batch consistency - the same cap, hour after hour, at the same weight and the same wall thickness.
The CCM-YSZG54 is the 54-cavity high-density platform for large cap plants: 100,000 caps per hour, molding precision with a stable yield of 99.5 percent or better, optimized for standard small beverage caps and proven in continuous 24/7 production. It is the model already in service at Yinlu.
The CCM-YSZG48 comes in two versions: Version A is tuned for standard 3025 water caps at up to 80,000 caps per hour, while Version B handles larger-diameter caps at up to 60,000 caps per hour. Both run continuous compression molding for plants scaling up water and dairy cap output.
The CCM-YSZG24 is the 24-cavity upgrade: an integrated rotary table and a high-precision dual-pump hydraulic system, 40,000 caps per hour, wide cap compatibility and fast mold change. Its low-temperature melting process saves energy and material and leaves no gate mark on the cap - which is why it is the main machine of choice for medium-sized factories that run several cap types on one line.
The CCM-JP24 (full model designation CCM-JP24D) is the entry platform and the best cost-performance option: 24 cavities, PP / PE / HDPE, up to 24,000 caps per hour and caps up to 55 mm outer diameter. The structure is simplified and stable, operation is straightforward, and there is no runner waste - a sensible starting point for new cap manufacturers with moderate budgets and frequent SKU changes.


What each platform actually runs
Standard beverage closures: 2622 CSD, water and CAF caps on 26 mm neck finish; 2722 water and CAF on 27 mm; 2925 water on 29 mm; 3025 water on 30 mm. The 28 mm family: 1881 CSD and CAF, 1810 hot-filling and water caps. Mid-size formats: 38 mm CAF, 38 mm smart and 38 mm combination caps. Large formats: the 48 mm smart cap on a 45 mm neck finish, and the 55 mm smart cap. Specialty items include liqueur inner caps to custom size, toothpaste caps on a 10 mm neck finish, and medical caps built to customer specification.
One rule decides the model more often than any other: the maximum cap diameter. The 64- and 48-cavity machines are rated to Φ45 mm, the 54-cavity to Φ35 mm, and the two 24-cavity platforms to Φ55 mm. A 48 mm smart cap, with its 45 mm neck finish, therefore belongs on the 24-cavity platform - not on the highest-output machine in the range. Getting this wrong at the specification stage is the most common and most expensive mistake in cap plant planning.
Three questions before you specify
First, output: the number of caps per hour you must hold, not the number you hope for on a good shift. Second, geometry: cap outer diameter, height and target weight all have to sit inside the limits in the table above, and the cap drawing - neck finish, thread, tamper-evident band - determines mold design. Third, plant conditions: grid stability and voltage fluctuation, ambient temperature, the automation level you intend to reach, and the downstream equipment the machine must hand over to. JEEPINE machines are built with wide-voltage tolerance specifically for grids and high-temperature conditions in Southeast Asia and Africa, where installations are widespread.
From one machine to a complete line
A compression molding machine is rarely the whole project. It can be integrated with cooling, cap sorting, slitting and folding for tamper-evident bands, printing, coding, online inspection and packaging to form a complete automated cap line. Beyond closures, JEEPINE also supplies preform injection molding machines, water treatment systems, bottle blowing machines, filling machines, capping machines, labelling machines, sleeve labelling machines and palletizing robots, so a project can be coordinated from one technical team instead of five suppliers.
Compliance and material
The machines carry CE, ISO and UL certification. They run PP, PE and HDPE. Closures intended for food-contact or pharmaceutical use are produced from compliant resin grades under frameworks such as GB 4806.7, EU 10/2011, FDA 21 CFR 177.1520 and USP <661> - the machine is built to process these resins precisely; final compliance of a closure always depends on the resin grade selected and the converter's own validation.
Support over the machine's life
Mold design and OEM customization are matched to the customer's cap drawing rather than to a catalogue. Fast mold change keeps multi-SKU plants productive; spare parts are universal, so local technicians can handle routine maintenance without waiting on an overseas shipment; and remote diagnostics shorten troubleshooting to hours instead of weeks.
Specify with four pieces of information
Send the cap drawing - neck finish, outer diameter, height and target weight - together with required output and shift pattern, plant power and grid conditions, and the downstream equipment you plan to run. With those four inputs, the model recommendation and quotation come back accurate the first time, rather than after two rounds of revision.
